Our 350-401 Dumps exam questions are often in short supply. Every day, large numbers of people crowd into our website to browser our 350-401 Dumps study materials. Then they will purchase various kinds of our 350-401 Dumps learning braindumps at once. With 350-401 Dumps practice materials, you don't need to spend a lot of time and effort on reviewing and preparing. For everyone, time is precious. Once it is time to submit your exercises, the system of the 350-401 Dumps preparation exam will automatically finish your operation.
CCNP Enterprise 350-401 Just have a try and you will love them!
You can trust in our quality of the 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Dumps exam questions and you can try it by free downloading the demos. If you believe in our products this time, you will enjoy the happiness of success all your life Our 350-401 Valid Test Camp learning quiz is the accumulation of professional knowledge worthy practicing and remembering, so you will not regret choosing our 350-401 Valid Test Camp study guide.
In the 21st century, all kinds of examinations are filled with the life of every student or worker. We need to pass some exams to get the corresponding certificates like 350-401 Dumps certification, so as to get the recognition of enterprises and society. However, passing an 350-401 Dumps exam is not easy, and a large number of people fail to pass it every year, as is the case with the 350-401 Dumps exam.
Cisco 350-401 Dumps - Then they will receive our mails in 5-10 minutes.
As we all know, 350-401 Dumps certificates are an essential part of one’s resume, which can make your resume more prominent than others, making it easier for you to get the job you want. For example, the social acceptance of 350-401 Dumps certification now is higher and higher. If you also want to get this certificate to increase your job opportunities, please take a few minutes to see our 350-401 Dumps training materials.
Once you compare our 350-401 Dumps study materials with the annual real exam questions, you will find that our 350-401 Dumps exam questions are highly similar to the real exam questions. We have strong strengths to assist you to pass the exam.
350-401 PDF DEMO:
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 5
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
With the help of our Axis ANVE practice guide, you don't have to search all kinds of data, because our products are enough to meet your needs. If you refuse to be an ordinary person, come to learn our Microsoft PL-600 preparation questions. Huawei H13-921_V1.5 - Nowadays, online shopping has been greatly developed, but because of the fear of some uncontrollable problems after payment, there are still many people don't trust to buy things online, especially electronic products. In order to help people pass the exam and gain the certification, we are glad to the HP HPE0-J68-KR study tool from our company for you. IBM C1000-204 - We really take the requirements of our worthy customers into account.
Updated: May 28, 2022