Our passing rate is 98%-100% and our 350-401 Valid test prep can guarantee that you can pass the exam easily and successfully. Our 350-401 Valid exam materials are highly efficient and useful and can help you pass the exam in a short time and save your time and energy. It is worthy for you to buy our 350-401 Valid quiz torrent and you can trust our product. Software version of 350-401 Valid real exam - It support simulation test system, and times of setup has no restriction. App online version of 350-401 Valid learning quiz - Be suitable to all kinds of equipment or digital devices. So of course we received sincere feed-backs from exam candidates which are maximum benefits for us.
The 350-401 Valid training materials are so very helpful.
By the PDF version, you can print the Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) guide torrent which is useful for you. If you like use paper to learn, you can print in PDF; if you like learn with electronic equipment, you can use our APP online version offline. Our Cisco practice test software will give you a real exam environment with multiple learning tools that allow you to do a selective study and will help you to get the job that you are looking for.
There are so many specialists who join together and contribute to the success of our 350-401 Valid guide quiz just for your needs. As well as responsible and patient staff who has being trained strictly before get down to business and interact with customers on our 350-401 Valid exam questions. You can contact with our service, and they will give you the most professional guide.
Cisco 350-401 Valid actual test guide is your best choice.
If you are a person who desire to move ahead in the career with informed choice, then the Cisco training material is quite beneficial for you. The 350-401 Valid pdf vce is designed to boost your personal ability in your industry. It just needs to spend 20-30 hours on the 350-401 Valid preparation, which can allow you to face with 350-401 Valid actual test with confidence. You will always get the latest and updated information about 350-401 Valid training pdf for study due to our one year free update policy after your purchase.
350-401 Valid training materials will definitely live up to your expectations. Not only our 350-401 Valid study materials contain the latest exam questions and answers, but also the pass rate is high as 98% to 100%.
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
We aimed to help our candidates get success in the Microsoft PL-300 practice test with less time and leas effort. For the complex part of our Microsoft SC-300 exam question, you may be too cumbersome, but our system has explained and analyzed this according to the actual situation to eliminate your doubts and make you learn better. With the best quality of Fortinet FCSS_SASE_AD-25 braindumps pdf from our website, getting certified will be easier and fast. Cisco 350-901 - We here tell you that there is no need to worry about. CWNP CWAP-405 - Our exam materials are collected from the real test center and edited by our experienced experts.
Updated: May 28, 2022