And the more you know, the more easily you can cope with the difficulties in your work. And the most important is that you can get the 200-301 Test Simulator certification. As old saying goes, knowledge is wealth. We Goldmile-Infobiz Cisco 200-301 Test Simulator exam training materials in full possession of the ability to help you through the certification. Goldmile-Infobiz website training materials are proved by many candidates, and has been far ahead in the international arena. Our Goldmile-Infobiz will be your best selection and guarantee to pass Cisco 200-301 Test Simulator exam certification.
CCNA 200-301 We can help you to achieve your goals.
CCNA 200-301 Test Simulator - Cisco Certified Network Associate Exam Goldmile-Infobiz can not only achieve your dreams, but also provide you one year of free updates and after-sales service. If you're also have an IT dream. Then go to buy Goldmile-Infobiz's Cisco Exam 200-301 Format exam training materials, it will help you achieve your dreams.
Perhaps you would spend less time and effort than the people who grasp fairly comprehensive expertise. The saying goes, all roads lead to Rome. Many people think that passing some difficult IT certification exams needs to be proficient in much of IT expertise and only these IT personnels who grasp the comprehensive IT knowledge would be able to enroll in the exam.
Cisco 200-301 Test Simulator - Third, the quality of the product.
The happiness from success is huge, so we hope that you can get the happiness after you pass 200-301 Test Simulator exam certification with our developed software. Your success is the success of our Goldmile-Infobiz, and therefore, we will try our best to help you obtain 200-301 Test Simulator exam certification. We will not only spare no efforts to design 200-301 Test Simulator exam materials, but also try our best to be better in all after-sale service.
It is the industry leader in providing IT certification information. To selecte Goldmile-Infobiz is to choose success.
200-301 PDF DEMO:
QUESTION NO: 1
Which statement about Link Aggregation when implemented on a Cisco Wireless LAN
Controller is true?
A. One functional physical port is needed to pass client traffic
B. The EtherChannel must be configured in "mode active"
C. When enabled the WLC bandwidth drops to 500 Mbps
D. To pass client traffic two or more ports must be configured.
Answer: A
Explanation:
Link aggregation (LAG) is a partial implementation of the 802.3ad port aggregation standard. It bundles all of the controller's distribution system ports into a single 802.3ad port channel.
Restriction for Link aggregation:
- LAG requires the EtherChannel to be configured for `mode on' on both the controller and the
Catalyst switch -> Answer B is not correct.
- If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller -> Answer A is not correct while answer D is correct.
Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/ b_cg75_chapter_0100010.html
QUESTION NO: 2
Drag and Drop Question
Drag and drop the WLAN components from the left onto the correct descriptions on the right.
Answer:
Explanation:
The service port can be used management purposes, primarily for out-of-band management.
However, AP management traffic is not possible across the service port. In most cases, the service port is used as a "last resort" means of accessing the controller GUI for management purposes. For example, in the case where the system distribution ports on the controller are down or their communication to the wired network is otherwise degraded.
A dynamic interface with the Dynamic AP Management option enabled is used as the tunnel source for packets from the controller to the access point and as the destination for CAPWAP packets from the access point to the controller.
The virtual interface is used to support mobility management, Dynamic Host Configuration Protocol
(DHCP) relay, and embedded Layer 3 security such as guest web authentication. It also maintains the
DNS gateway host name used by Layer 3 security and mobility managers to verify the source of certificates when Layer 3 web authorization is enabled.
Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-5/config- guide/b_cg85/ports_and_interfaces.html
QUESTION NO: 3
Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the
VLANs.
All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway.
What is true about this configuration?
A. These commands need to be added to the configuration:
C-router(config)# router rip
C-router(config-router)# network 172.19.0.0
B. These commands need to be added to the configuration:
C-router(config)# router ospf 1
C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
C. These commands need to be added to the configuration:
C-router(config)# router eigrp 123
C-router(config-router)# network 172.19.0.0
D. No further routing configuration is required.
Answer: D
Explanation:
Since all the same router (C-router) is the default gateway for all three VLANs, all traffic destined to a different VLAN will be sent to the C-router. The C-router will have knowledge of all three networks since they will appear as directly connected in the routing table. Since the C-router already knows how to get to all three networks, no routing protocols need to be configured.
QUESTION NO: 4
Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two)
A. Verify the time zone.
B. Disable NTP broadcasts
C. Set the NTP server private key
D. Specify the IP address of the NTP server
E. Enable NTP authentication.
Answer: D,E
Explanation:
To configure authentication, perform this task in privileged mode:
Step 1: Configure an authentication key pair for NTP and specify whether the key will be trusted or untrusted.
Step 2: Set the IP address of the NTP server and the public key.
Step 3: Enable NTP client mode.
Step 4: Enable NTP authentication.
Step 5: Verify the NTP configuration.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4000/8-
2glx/configuration/guide/ ntp.html
QUESTION NO: 5
A router running EIGRP has learned the same route from two different paths. Which parameter does the router use to select the best path?
A. administrative distance
B. as-path
C. metric
D. cost
Answer: C
Explanation:
If a router learns two different paths for the same network from the same routing protocol, it has to decide which route is better and will be placed in the routing table. Metric is the measure used to decide which route is better (lower number is better). Each routing protocol uses its own metric.
For example, RIP uses hop counts as a metric, while OSPF uses cost.
https://study-ccna.com/administrative-distance-metric/
There are quite a few candidates of CompTIA CS0-003 certification exam have already started his career, and there are many examinees facing other challenges in life, so we provide candidates with the most efficient review method of CompTIA CS0-003 exam. SAP C-ABAPD-2507 - If you buy Goldmile-Infobiz exam dumps, you will obtain free update for a year. HP HPE3-CL06 exam simulations files can help you obtain an IT certification. Adobe AD0-E117 - All Of IT staff knows it is very difficult to get IT certificate. ACAMS CAMS7 - We are sure about "pass Guaranteed" & "Money Back Guaranteed" so that you can feel safe and worry-free on our website.
Updated: May 28, 2022