Also, you can make notes on your papers to help you memorize and understand the difficult parts of the 350-401 Study Center exam questions. In order to help you enjoy the best learning experience, our PDF 350-401 Study Center practice engine supports you download on your computers and print on papers. You must be inspired by your interests and motivation. Goldmile-Infobiz real questions and answers are compiled by lots of IT experts with abundant experiences. So it has very high value. But you are lucky, we can provide you with well-rounded services on 350-401 Study Center practice braindumps to help you improve ability.
CCNP Enterprise 350-401 It costs both time and money.
The 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Study Center training pdf provided by Goldmile-Infobiz is really the best reference material you can get from anywhere. Besides, the pollster conducted surveys of public opinions of our 350-401 Reliable Exam Dumps Questions study engine and get desirable outcomes that more than 98 percent of exam candidates feel rewarding after using our 350-401 Reliable Exam Dumps Questions actual exam. And we enjoy their warm feedbacks to show and prove that we really did a good job in this career.
The 350-401 Study Center practice exam we offered is designed with the real questions that will help you in enhancing your knowledge about the 350-401 Study Center certification exam. Our online test engine will improve your ability to solve the difficulty of 350-401 Study Center real questions and get used to the atmosphere of the formal test. Our experts created the valid 350-401 Study Center study guide for most of candidates to help them get good result with less time and money.
But our Cisco 350-401 Study Center exam questions have made it.
Our 350-401 Study Center practice dumps are so popular that all our customers are giving high praise on its high-quality to help them pass the exams. Numerous of warming feedbacks from our worthy customers give us data and confidence. We have clear data collected from customers who chose our 350-401 Study Center training engine, the passing rate is 98-100 percent. So your chance of getting success will be increased greatly by our 350-401 Study Center exam questions!
Every page is carefully arranged by our experts with clear layout and helpful knowledge to remember. Our 350-401 Study Center exam questions just focus on what is important and help you achieve your goal.
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
with our Oracle 1Z1-947 exam dumps for 20 to 30 hours, we can claim that our customers are confident to take part in your Oracle 1Z1-947 exam and pass it for sure. So our EMC D-SF-A-01practice materials have great brand awareness in the market. Our company attaches great importance to overall services on our IBM C1000-201 study guide, if there is any problem about the delivery of IBM C1000-201 exam materials, please let us know, a message or an email will be available. SAP C_THR81_2505 - The software boosts varied self-learning and self-assessment functions to check the results of the learning. We guarantee that if you follow the guidance of our Cisco 100-160 learning materials, you will pass the exam without a doubt and get a certificate.
Updated: May 28, 2022