With great outcomes of the passing rate upon to 98-100 percent, our 350-401 Study Guide practice engine is totally the perfect ones. We never boost our achievements on our 350-401 Study Guide exam questions, and all we have been doing is trying to become more effective and perfect as your first choice, and determine to help you pass the 350-401 Study Guide study materials as efficient as possible. Just to try on our 350-401 Study Guide training guide, and you will love it. Tens of thousands of the candidates are learning on our 350-401 Study Guide practice engine. First of all, our 350-401 Study Guide study dumps cover all related tests about computers. Besides, you can have an experimental look of demos and get more information of 350-401 Study Guide real questions.
Try our 350-401 Study Guide study tool and absorb new knowledge.
You will love our 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Study Guide exam questions as long as you have a try! Our 350-401 Reliable Test Camp Pdf study material always regards helping students to pass the exam as it is own mission. And we have successfully helped numerous of the candidates pass their exams.
We understand your drive of the certificate, so you have a focus already and that is a good start. The sources and content of our 350-401 Study Guide practice dumps are all based on the real 350-401 Study Guide exam. And they are the masterpieces of processional expertise these area with reasonable prices.
Cisco 350-401 Study Guide - How diligent they are!
With 350-401 Study Guide practice materials, you don't need to spend a lot of time and effort on reviewing and preparing. For everyone, time is precious. Office workers and mothers are very busy at work and home; students may have studies or other things. Using 350-401 Study Guide guide questions, you only need to spend a small amount of time to master the core key knowledge, pass the 350-401 Study Guide exam, and get a certificate.
If you are satisfied with our 350-401 Study Guide training guide, come to choose and purchase. If you buy the Software or the APP online version of our 350-401 Study Guide study materials, you will find that the timer can aid you control the time.
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
Microsoft AZ-204-KR - Thus most of the questions are repeated in exams and our experts after studying the previous exam have sorted out the most important questions and prepared dumps out of them. All experts and professors of our company have been trying their best to persist in innovate and developing the Appian ACD201 test training materials all the time in order to provide the best products for all people and keep competitive in the global market. If you study on our test engine, your preparation time of the HP HPE6-A87 guide braindumps will be greatly shortened. Broadcom 250-584 - We cannot predicate what will happen in the future. We never avoid our responsibility of offering help for exam candidates like you, so choosing our Microsoft PL-400-KR training guide means you choose success.
Updated: May 28, 2022