If you still desperately cram knowledge and spend a lot of precious time and energy to prepare for passing Cisco certification 350-401 Test Tips exam, and at the same time do not know how to choose a more effective shortcut to pass Cisco certification 350-401 Test Tips exam. Now Goldmile-Infobiz provide you a effective method to pass Cisco certification 350-401 Test Tips exam. It will play a multiplier effect to help you pass the exam. Our 350-401 Test Tips test questions are compiled by domestic first-rate experts and senior lecturer and the contents of them contain all the important information about the test and all the possible answers of the questions which maybe appear in the test. You can use the practice test software to check your learning outcomes. Now you can free download part of practice questions and answers of Cisco certification 350-401 Test Tips exam on Goldmile-Infobiz.
CCNP Enterprise 350-401 I wish you good luck.
CCNP Enterprise 350-401 Test Tips - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Also, there will have no extra restrictions to your learning because different versions have different merits. IT authentication certificate is a best proof for your IT professional knowledge and experience. Cisco Valid 350-401 Exam Collection Pdf is a very important certification exam in the IT industry and passing Cisco certification Valid 350-401 Exam Collection Pdf exam is very difficult.
The experts and professors of our company have designed the three different versions of the 350-401 Test Tips prep guide, including the PDF version, the online version and the software version. Now we are going to introduce the online version for you. There are a lot of advantages about the online version of the 350-401 Test Tips exam questions from our company.
Cisco 350-401 Test Tips - So, the competition is in fierce in IT industry.
Our 350-401 Test Tips learning materials will help you circumvent those practice engine with low quality and help you redress the wrongs you may have and will have in the 350-401 Test Tips study quiz before heads. That is the reason why we make it without many sales tactics to promote our 350-401 Test Tips exam braindumps. And our 350-401 Test Tips training prep is regarded as the most pppular exam tool in the market and you can free download the demos to check the charming.
There is no better certification training materials than Goldmile-Infobiz dumps. Instead of wasting your time on preparing for 350-401 Test Tips exam, you should use the time to do significant thing.
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
Presiding over the line of our SAP C_S4CPB_2508 practice materials over ten years, our experts are proficient as elites who made our SAP C_S4CPB_2508 learning questions, and it is their job to officiate the routines of offering help for you. Adobe AD0-E608-KR - Moreover, the colleagues and the friends with IT certificate have been growing. Under coordinated synergy of all staff, our Juniper JN0-650 guide materials achieved to a higher level of perfection by keeping close attention with the trend of dynamic market. If you have any questions about purchasing Alibaba SAE-C01 exam software, you can contact with our online support who will give you 24h online service. So they can help you save time and cut down additional time to focus on the Amazon AWS-Certified-Developer-Associate practice exam review only.
Updated: May 28, 2022