Our training materials, including questions and answers, the pass rate can reach 100%. With Goldmile-Infobiz Cisco 350-401 Exam Questions Fee exam training materials, you can begin your first step forward. When you get the certification of Cisco 350-401 Exam Questions Fee exam, the glorious period of your career will start. Goldmile-Infobiz can provide you a pertinence training and high quality exercises, which is your best preparation for your first time to attend Cisco certification 350-401 Exam Questions Fee exam. Goldmile-Infobiz's exercises are very similar with the real exam, which can ensure you a successful passing the Cisco certification 350-401 Exam Questions Fee exam. When you are faced with the real exam, you can pass Cisco 350-401 Exam Questions Fee test easily.
CCNP Enterprise 350-401 It is so cool even to think about it.
Our 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Exam Questions Fee practice questions and answers are created according to the requirement of the certification center and the latest exam information. The easy language does not pose any barrier for any learner. The complex portions of the 350-401 Free Sample certification syllabus have been explained with the help of simulations and real-life based instances.
Our 350-401 Exam Questions Fee preparationdumps are considered the best friend to help the candidates on their way to success for the exactness and efficiency based on our experts’ unremitting endeavor. This can be testified by our claim that after studying with our 350-401 Exam Questions Fee actual exam for 20 to 30 hours, you will be confident to take your 350-401 Exam Questions Fee exam and successfully pass it. Tens of thousands of our loyal customers relayed on our 350-401 Exam Questions Fee preparation materials and achieved their dreams.
Cisco 350-401 Exam Questions Fee - Their efficiency has far beyond your expectation!
We has been developing faster and faster and gain good reputation in the world owing to our high-quality 350-401 Exam Questions Fee exam materials and high passing rate. Since we can always get latest information resource, we have unique advantages on 350-401 Exam Questions Fee study guide. Our high passing rate is the leading position in this field. We are the best choice for candidates who are eager to pass 350-401 Exam Questions Fee exams and acquire the certifications. Our 350-401 Exam Questions Fee practice engine will be your best choice to success.
It is fast and convenient out of your imagination. Unlike other kinds of exam files which take several days to wait for delivery from the date of making a purchase, our 350-401 Exam Questions Fee study materials can offer you immediate delivery after you have paid for them.
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 4
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
Salesforce B2C-Commerce-Architect - You will never be frustrated by the fact that you can't solve a problem. Meanwhile, if you want to keep studying this course , you can still enjoy the well-rounded services by DSCI DCPLA test prep, our after-sale services can update your existing DSCI DCPLA study quiz within a year and a discount more than one year. Our PECB ISO-9001-Lead-Auditor study materials are very popular in the international market and enjoy wide praise by the people in and outside the circle. Our Amazon Data-Engineer-Associate exam questions can assure you that you will pass the Amazon Data-Engineer-Associate exam as well as getting the related certification under the guidance of our Amazon Data-Engineer-Associate study materials as easy as pie. For the convenience of the users, the Amazon SAP-C02-KR test materials will be updated on the homepage and timely update the information related to the qualification examination.
Updated: May 28, 2022