You’ve heard it right. We are so confident about our 350-401 Valid Test Tutorial exam dumps for Cisco 350-401 Valid Test Tutorial exam that we are offering a money back guarantee, if you fail. Yes you read it right, if our 350-401 Valid Test Tutorial exam braindumps didn’t help you pass, we will issue a refund - no other questions asked. When you complete your payment, you will receive an email attached with 350-401 Valid Test Tutorial practice pdf, then you can instantly download it and install on your phone or computer for study. The high efficiency preparation by 350-401 Valid Test Tutorial exam dumps can ensure you 100% pass with ease. You can totally rely on us!
CCNP Enterprise 350-401 So customer orientation is the beliefs we honor.
With our professional experts’ unremitting efforts on the reform of our 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Valid Test Tutorial guide materials, we can make sure that you can be focused and well-targeted in the shortest time when you are preparing a test, simplify complex and ambiguous contents. Besides, the pass rate of our Exam 350-401 Cram Review exam questions are unparalled high as 98% to 100%, you will get success easily with our help. There are so many features to show that our Exam 350-401 Cram Review study guide surpasses others.
No other vendors can challenge our data in this market. At the same time, by studying with our 350-401 Valid Test Tutorial practice materials, you avoid wasting your precious time on randomly looking for the key point information. We provide a smooth road for you to success.
Cisco 350-401 Valid Test Tutorial - Your life will be even more exciting.
After our practice materials were released ten years ago, they have been popular since then and never lose the position of number one in this area. Our 350-401 Valid Test Tutorial practice quiz has authority as the most professional exam material unlike some short-lived 350-401 Valid Test Tutorial exam materials. Targeting exam candidates of the exam, we have helped over tens of thousands of exam candidates achieved success now. So you can be successful by make up your mind of our 350-401 Valid Test Tutorial training guide.
The price of our 350-401 Valid Test Tutorial learning guide is among the range which you can afford and after you use our 350-401 Valid Test Tutorial study materials you will certainly feel that the value of the 350-401 Valid Test Tutorial exam questions far exceed the amount of the money you pay for the pass rate of our practice quiz is 98% to 100% which is unmarched in the market. Choosing our 350-401 Valid Test Tutorial study guide equals choosing the success and the perfect service.
350-401 PDF DEMO:
QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 2
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
Lpi 101-500 - Are you still satisfied with your present job? Do you still have the ability to deal with your job well? Do you think whether you have the competitive advantage when you are compared with people working in the same field? If your answer is no，you are a right place now. We can promise that we will provide you with quality products, reasonable price and professional after sale service on our IIA IIA-CIA-Part3-KR learning guide. So our Real Estate Licensing Virginia-Real-Estate-Salesperson training prep is definitely making your review more durable. Pure Storage FAAA_005 - The most advantage of the online version is that this version can support all electronica equipment. Also we offer free demos for you to check out the validity and precise of our SAP C-ARCIG-2508 training materials.
Updated: May 28, 2022