The results are accurate. You need to concentrate on memorizing the wrong questions. Our 200-301 Reliable Test Study Guide learning questions have its own advantage. You can have a quick revision of the 200-301 Reliable Test Study Guide study materials in your spare time. Also, you can memorize the knowledge quickly. They are PDF version, online test engines and windows software of the 200-301 Reliable Test Study Guide study materials.
CCNA 200-301 How to get to heaven? Shortcart is only one.
CCNA 200-301 Reliable Test Study Guide - Cisco Certified Network Associate Exam I can say without hesitation that this is definitely a targeted training material. Try Goldmile-Infobiz Cisco 200-301 Interactive EBook exam dumps. Goldmile-Infobiz dumps can absolutely let you get an unexpected effect.
Someone asked, where is success? Then I tell you, success is in Goldmile-Infobiz. Select Goldmile-Infobiz is to choose success. Goldmile-Infobiz's Cisco 200-301 Reliable Test Study Guide exam training materials can help all candidates to pass the IT certification exam.
Cisco 200-301 Reliable Test Study Guide - Goldmile-Infobiz is worthy your trust.
To help you get the Cisco exam certification, we provide you with the best valid 200-301 Reliable Test Study Guide pdf prep material. The customizable and intelligence 200-301 Reliable Test Study Guide test engine will bring you to a high efficiency study way. The 200-301 Reliable Test Study Guide test engine contains self-assessment features like marks, progress charts, etc. Besides, the Easy-to-use 200-301 Reliable Test Study Guide layout will facilitate your preparation for 200-301 Reliable Test Study Guide real test. You can pass your 200-301 Reliable Test Study Guide certification without too much pressure.
200-301 Reliable Test Study Guide exam seems just a small exam, but to get the 200-301 Reliable Test Study Guide certification exam is to be reckoned in your career. Such an international certification is recognition of your IT skills.
200-301 PDF DEMO:
QUESTION NO: 1
Which statement about Link Aggregation when implemented on a Cisco Wireless LAN
Controller is true?
A. One functional physical port is needed to pass client traffic
B. The EtherChannel must be configured in "mode active"
C. When enabled the WLC bandwidth drops to 500 Mbps
D. To pass client traffic two or more ports must be configured.
Answer: A
Explanation:
Link aggregation (LAG) is a partial implementation of the 802.3ad port aggregation standard. It bundles all of the controller's distribution system ports into a single 802.3ad port channel.
Restriction for Link aggregation:
- LAG requires the EtherChannel to be configured for `mode on' on both the controller and the
Catalyst switch -> Answer B is not correct.
- If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller -> Answer A is not correct while answer D is correct.
Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/ b_cg75_chapter_0100010.html
QUESTION NO: 2
Drag and Drop Question
Drag and drop the WLAN components from the left onto the correct descriptions on the right.
Answer:
Explanation:
The service port can be used management purposes, primarily for out-of-band management.
However, AP management traffic is not possible across the service port. In most cases, the service port is used as a "last resort" means of accessing the controller GUI for management purposes. For example, in the case where the system distribution ports on the controller are down or their communication to the wired network is otherwise degraded.
A dynamic interface with the Dynamic AP Management option enabled is used as the tunnel source for packets from the controller to the access point and as the destination for CAPWAP packets from the access point to the controller.
The virtual interface is used to support mobility management, Dynamic Host Configuration Protocol
(DHCP) relay, and embedded Layer 3 security such as guest web authentication. It also maintains the
DNS gateway host name used by Layer 3 security and mobility managers to verify the source of certificates when Layer 3 web authorization is enabled.
Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-5/config- guide/b_cg85/ports_and_interfaces.html
QUESTION NO: 3
Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the
VLANs.
All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway.
What is true about this configuration?
A. These commands need to be added to the configuration:
C-router(config)# router rip
C-router(config-router)# network 172.19.0.0
B. These commands need to be added to the configuration:
C-router(config)# router ospf 1
C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
C. These commands need to be added to the configuration:
C-router(config)# router eigrp 123
C-router(config-router)# network 172.19.0.0
D. No further routing configuration is required.
Answer: D
Explanation:
Since all the same router (C-router) is the default gateway for all three VLANs, all traffic destined to a different VLAN will be sent to the C-router. The C-router will have knowledge of all three networks since they will appear as directly connected in the routing table. Since the C-router already knows how to get to all three networks, no routing protocols need to be configured.
QUESTION NO: 4
Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two)
A. Verify the time zone.
B. Disable NTP broadcasts
C. Set the NTP server private key
D. Specify the IP address of the NTP server
E. Enable NTP authentication.
Answer: D,E
Explanation:
To configure authentication, perform this task in privileged mode:
Step 1: Configure an authentication key pair for NTP and specify whether the key will be trusted or untrusted.
Step 2: Set the IP address of the NTP server and the public key.
Step 3: Enable NTP client mode.
Step 4: Enable NTP authentication.
Step 5: Verify the NTP configuration.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4000/8-
2glx/configuration/guide/ ntp.html
QUESTION NO: 5
A router running EIGRP has learned the same route from two different paths. Which parameter does the router use to select the best path?
A. administrative distance
B. as-path
C. metric
D. cost
Answer: C
Explanation:
If a router learns two different paths for the same network from the same routing protocol, it has to decide which route is better and will be placed in the routing table. Metric is the measure used to decide which route is better (lower number is better). Each routing protocol uses its own metric.
For example, RIP uses hop counts as a metric, while OSPF uses cost.
https://study-ccna.com/administrative-distance-metric/
You will never regret choosing our Cisco 200-301 test answers as your practice materials because we will show you the most authoritative study guide. We provide the HP HPE3-CL04 test engine with self-assessment features for enhanced progress. This Cisco braindump study package contains IBM C1000-189 latest questions and answers from the real IBM C1000-189 exam. SAP C-SIGPM-2403 - We get first-hand information; 2. At the same time, HP HPE3-CL07 preparation baindumps can keep pace with the digitized world by providing timely application.
Updated: May 28, 2022