Goldmile-Infobizは数年にわたりCisco 350-401キャリアパス資格認定試験の研究に取り組んで、量豊かな問題庫があるし、豊富な経験を持ってあなたが認定試験に効率的に合格するのを助けます。350-401キャリアパス資格認定試験に合格できるかどうかには、重要なのは正確の方法で、復習教材の量ではありません。だから、Goldmile-InfobizはあなたがCisco 350-401キャリアパス資格認定試験にパースする正確の方法です。 今の社会はますます激しく変化しているから、私たちはいつまでも危機意識を強化します。キャンパース内のIT知識を学ぶ学生なり、IT職人なり、350-401キャリアパス試験資格認証証明書を取得して、社会需要に応じて自分の能力を高めます。 350-401キャリアパス資料を勉強するとき、何か質問がありましたら、弊社と連絡できます。
CCNP Enterprise 350-401 迷ってないください。
Goldmile-Infobizの問題集はIT専門家がCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)キャリアパス「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験について自分の知識と経験を利用して研究したものでございます。 あなたは一部の試用問題と解答を無料にダウンロードすることができます。Goldmile-InfobizのCiscoの350-401 受験準備の試験中に絶対な方法で転送することでなく、Goldmile-Infobizは真実かつ全面的な試験問題と解答を提供していますから、当社がオンラインするユニークなのCiscoの350-401 受験準備の試験トレーニング資料を利用したら、あなたが気楽に試験に合格することができるようになります。
弊社が提供したすべての勉強資料と他のトレーニング資料はコスト効率の良い製品で、サイトが一年間の無料更新サービスを提供します。ですから、弊社のトレーニング製品はあなたが試験に合格することを助けにならなかったら、全額で返金することを保証します。Ciscoの350-401キャリアパスのオンラインサービスのスタディガイドを買いたかったら、Goldmile-Infobizを買うのを薦めています。
Cisco 350-401キャリアパス - 資料は問題集と解答が含まれています。
神様は私を実力を持っている人間にして、美しい人形ではないです。IT業種を選んだ私は自分の実力を証明したのです。しかし、神様はずっと私を向上させることを要求します。Ciscoの350-401キャリアパス試験を受けることは私の人生の挑戦の一つです。でも大丈夫です。Goldmile-InfobizのCiscoの350-401キャリアパス試験トレーニング資料を購入しましたから。すると、Ciscoの350-401キャリアパス試験に合格する実力を持つようになりました。 Goldmile-InfobizのCiscoの350-401キャリアパス試験トレーニング資料を持つことは明るい未来を持つことと同じです。
あなたの独自の品質を向上させるだけでなく、完璧な人生価値を実現することも助けます。あなたが悲しいとき、勉強したほうがいいです。
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
Cisco 200-301 - ここにはあなたが最も欲しいものがありますから。 CiscoのMicrosoft AZ-900認定試験に合格のにどうしたらいいかと困っているより、パソコンを起動して、Goldmile-Infobizをクリックしたほうがいいです。 Cisco 300-425J - これは完全に実際の試験雰囲気とフォーマットをシミュレートするソフトウェアですから。 Amazon AIF-C01 - しかし、難しいといっても、高い点数を取って楽に試験に合格できないというわけではないです。 CiscoのAmazon SAP-C02-KRの認証試験の高品質の資料を提供しているユニークなサイトはGoldmile-Infobizです。
Updated: May 28, 2022