Ciscoの350-401対応内容は専門知識と情報技術の検査として認証試験で、Goldmile-Infobizはあなたに一日早くCiscoの認証試験に合格させて、多くの人が大量の時間とエネルギーを費やしても無駄になりました。Goldmile-Infobizにその問題が心配でなく、わずか20時間と少ないお金をを使って楽に試験に合格することができます。Goldmile-Infobizは君に対して特別の訓練を提供しています。 この問題集は間違いなくあなたの成功への近道で、あなたが十分に350-401対応内容試験を準備させます。チャンスは常に準備ができあがった者に属します。 Goldmile-Infobizが提供した商品をご利用してください。
CCNP Enterprise 350-401 心配なく我々の真題を利用してください。
CCNP Enterprise 350-401対応内容 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) 試験に失敗したら全額で返金するという承諾があるとは言え、弊社の商品を利用したほとんどの受験生は試験に合格しました。 Goldmile-Infobizの350-401 復習問題集問題集を使用した後、あなたはたくさんのの350-401 復習問題集試験資料を勉強するとか、専門のトレーニング機構に参加するとかなど必要がないと認識します。Goldmile-Infobiz350-401 復習問題集問題集は試験の範囲を広くカバーするだけでなく、質は高いです。
たくさんの時間と精力で試験に合格できないという心配な心情があれば、我々Goldmile-Infobizにあなたを助けさせます。多くの受験生は我々のソフトでCiscoの350-401対応内容試験に合格したので、我々は自信を持って我々のソフトを利用してあなたはCiscoの350-401対応内容試験に合格する保障があります。IT業界の発展とともに、IT業界で働いている人への要求がますます高くなります。
Cisco 350-401対応内容 - それで、不必要な損失を避けできます。
350-401対応内容問題集は一年間で無料更新サービスを提供することができ、350-401対応内容認定試験の合格に大変役に立ちます。そして、もし350-401対応内容問題集の更新版があれば、お客様にお送りいたします。350-401対応内容問題集は全面的かつわかりやすいです。あなたは350-401対応内容問題集をちゃんと覚えると、350-401対応内容試験に合格することは簡単です。では、試験を心配するより、今から行動しましょう。
弊社のCiscoの350-401対応内容練習問題を利用したら、あなたは気楽に勉強するだけではなく、順調に試験に合格します。多くの人々はCiscoの350-401対応内容試験に合格できるのは難しいことであると思っています。
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 4
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
Microsoft GH-300-JPN試験資料の3つのバージョンのなかで、PDFバージョンのMicrosoft GH-300-JPNトレーニングガイドは、ダウンロードと印刷でき、受験者のために特に用意されています。 他の人はあちこちでCisco Huawei H28-315_V1.0試験資料を探しているとき、あなたはすでに勉強中で、準備階段でライバルに先立ちます。 EXIN PR2F-JPN - IT業界ではさらに強くなるために強い専門知識が必要です。 そして、私たちは十分な耐久力を持って、ずっとASQ CMQ-OE練習資料の研究に取り組んでいます。 Microsoft AZ-204-KR - Goldmile-Infobizだけ全面と高品質の問題集があるのではGoldmile-Infobizの専門家チームが彼らの長年のIT知識と豊富な経験で研究してしました。
Updated: May 28, 2022