Goldmile-Infobizの350-401必殺問題集問題集を使用した後、あなたはたくさんのの350-401必殺問題集試験資料を勉強するとか、専門のトレーニング機構に参加するとかなど必要がないと認識します。Goldmile-Infobiz350-401必殺問題集問題集は試験の範囲を広くカバーするだけでなく、質は高いです。Goldmile-Infobizの350-401必殺問題集問題集を購入し勉強するだけ、あなたは試験にたやすく合格できます。 IT業界の発展とともに、IT業界で働いている人への要求がますます高くなります。競争の中で排除されないように、あなたはCiscoの350-401必殺問題集試験に合格しなければなりません。 人に引けをとりたくないあなたはCisco 350-401必殺問題集資格認定を取得したいですか。
350-401必殺問題集練習資料が最も全面的な参考書です。
CCNP Enterprise 350-401必殺問題集 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Goldmile-Infobizだけ全面と高品質の問題集があるのではGoldmile-Infobizの専門家チームが彼らの長年のIT知識と豊富な経験で研究してしました。 Cisco 350-401 資格難易度認証試験に合格することが簡単ではなくて、Cisco 350-401 資格難易度証明書は君にとってはIT業界に入るの一つの手づるになるかもしれません。しかし必ずしも大量の時間とエネルギーで復習しなくて、弊社が丹精にできあがった問題集を使って、試験なんて問題ではありません。
多くの時間と労力をかかってCiscoの350-401必殺問題集認定試験に合格するを冒険にすると代わりGoldmile-Infobizが提供した問題集を利用してわずか一度お金かかって合格するのは価値があるでしょう。今の社会の中で時間がそんなに重要で最も保障できるGoldmile-Infobizを選ばましょう。
Cisco 350-401必殺問題集 - 試験に失敗したら、全額で返金いたします。
Ciscoの350-401必殺問題集認定試験の最新教育資料はGoldmile-Infobizの専門チームが研究し続けてついに登場し、多くの人の夢が実現させることができます。今のIT業界の中で、自分の地位を固めたくて知識と情報技術を証明したいのもっとも良い方法がCiscoの350-401必殺問題集認定試験でございます。がCiscoの350-401必殺問題集「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認定試験の合格書を取ったら仕事の上で大きな変化をもたらします。
君が後悔しないようにもっと少ないお金を使って大きな良い成果を取得するためにGoldmile-Infobizを選択してください。Goldmile-Infobizはまた一年間に無料なサービスを更新いたします。
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
Cisco 300-715J - 何の問題があったらお気軽に聞いてください。 CiscoのAmazon DOP-C02-JPNの認証試験について、あなたは異なるサイトや書籍で色々な問題を見つけることができます。 Microsoft DP-900-KR試験がユニバーサルになりましたから、あなたはGoldmile-Infobiz のCiscoのMicrosoft DP-900-KR試験問題と解答￥を利用したらきっと試験に合格するができます。 Goldmile-Infobizは専門的にCiscoのCisco 700-246試験の最新問題と解答を提供するサイトで、Cisco 700-246についての知識をほとんどカバーしています。 Amazon SAP-C02-KR - 近年、IT業種の発展はますます速くなることにつれて、ITを勉強する人は急激に多くなりました。
Updated: May 28, 2022