無論Goldmile-InfobizのCiscoの350-401試験解答問題集が一番頼りになります。Goldmile-Infobizには専門的なエリート団体があります。認証専門家や技術者及び全面的な言語天才がずっと最新のCiscoの350-401試験解答試験を研究していて、最新のCiscoの350-401試験解答問題集を提供します。 Goldmile-InfobizのCiscoの350-401試験解答試験トレーニング資料はあなたがCiscoの350-401試験解答認定試験に合格することを助けます。この認証を持っていたら、あなたは自分の夢を実現できます。 もし君の予算がちょっと不自由で、おまけに質の良いCiscoの350-401試験解答試験トレーニング資料を購入したいなら、Goldmile-InfobizのCiscoの350-401試験解答試験トレーニング資料を選択したほうが良いです。
CCNP Enterprise 350-401 信じないでしょうか。
Ciscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)試験解答ソフトを使用するすべての人を有効にするために最も快適なレビュープロセスを得ることができ、我々は、Ciscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)試験解答の資料を提供し、PDF、オンラインバージョン、およびソフトバージョンを含んでいます。 しかし、これは本当のことですよ。350-401 最新対策問題認定試験の準備を効率的にするために、どんなツールが利用に値するものかわかっていますか。
我々ができるのはあなたにより速くCiscoの350-401試験解答試験に合格させます。数年間の発展で我々Goldmile-Infobizはもっと多くの資源と経験を得ています。改善されているソフトはあなたのCiscoの350-401試験解答試験の復習の効率を高めることができます。
Cisco 350-401試験解答 - 無事試験に合格しました。
Goldmile-Infobizは君の成功のために、最も質の良いCiscoの350-401試験解答試験問題と解答を提供します。もし君はいささかな心配することがあるなら、あなたはうちの商品を購入する前に、Goldmile-Infobizは無料でサンプルを提供することができます。あなたはGoldmile-InfobizのCiscoの350-401試験解答問題集を購入した後、私たちは一年間で無料更新サービスを提供することができます。
我々Goldmile-InfobizのCisco 350-401試験解答試験問題と試験解答の正確さは、あなたの試験準備をより簡単にし、あなたが試験に高いポイントを得ることを保証します。Cisco 350-401試験解答資格試験に参加する意向があれば、当社のGoldmile-Infobizから自分に相応しい受験対策解説集を選らんで、認定試験の学習教材として勉強します。
350-401 PDF DEMO:
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 5
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
あなたは弊社の商品を利用して、一回でCiscoのMicrosoft AZ-305-KR試験に合格できなかったら、弊社は全額で返金することを承諾いたします。 IIA IIA-CIA-Part2-JPN試験は難しいです。 Amazon SAA-C03 - あなたが本当にそれぞれの質問を把握するように、あなたが適切なトレーニングと詳細な分析を得ることができますから。 Cisco Microsoft DP-700J試験の合格のために、Goldmile-Infobizを選択してください。 HP HPE2-W12 - 我々はあなたのIT業界での発展にヘルプを提供できると希望します。
Updated: May 28, 2022