It is the leader in all training materials. It not only can help you to pass the exam , you can also improve your knowledge and skills. Help you in your career in your advantage successfully. You can find their real comments in the comments sections. There must be good suggestions for you on the 350-401 Test Dumps Demo learning quiz as well. Dreams and hopes are important, but more important is to go to practice and prove.
CCNP Enterprise 350-401 The dumps are provided by Goldmile-Infobiz.
Goldmile-Infobiz will provide good training tools for your Cisco certification 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Test Dumps Demo exam and help you pass Cisco certification 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Test Dumps Demo exam. However, our promise of "No help, full refund" doesn't shows our no confidence to our products; oppositely, it expresses our most sincere and responsible attitude to reassure our customers. With our professional VCE 350-401 Dumps exam software, you will be at ease about your VCE 350-401 Dumps exam, and you will be satisfied with our after-sale service after you have purchased our VCE 350-401 Dumps exam software.
A lot of people who participate in the IT professional certification exam was to use Goldmile-Infobiz's practice questions and answers to pass the exam, so Goldmile-Infobiz got a high reputation in the IT industry. Goldmile-Infobiz is a convenient website to provide training resources for IT professionals to participate in the certification exam. Goldmile-Infobiz have different training methods and training courses for different candidates.
Cisco 350-401 Test Dumps Demo - It can help you to pass the exam successfully.
Do you have tried the 350-401 Test Dumps Demo online test engine? Here we will recommend the 350-401 Test Dumps Demo online test engine offered by Goldmile-Infobiz for all of you. Firstly, 350-401 Test Dumps Demo online training can simulate the actual test environment and bring you to the mirror scene, which let you have a good knowledge of the actual test situation. Secondly, the 350-401 Test Dumps Demo online practice allows self-assessment, which can bring you some different experience during the preparation. You can adjust your 350-401 Test Dumps Demo study plan according to the test result after each practice test.
Only Goldmile-Infobiz can guarantee you 100% success. Goldmile-Infobiz allows you to have a bright future.
350-401 PDF DEMO:
QUESTION NO: 1 Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a Cisco operating system. When all physical connections are mode, the port channel does not establish. Based on the configuration excerpt of SW3, what is the cause of the problem? A. The port-channel interface lead balance should be set to src-mac B. The port-channel trunk is not allowing the native VLAN. C. The port-channel should be set to auto. D. The port channel on SW2 is using an incompatible protocol. Answer: D Explanation: The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 2 Which statement about multicast RPs is true? A. RPs are required for protocol independent multicast sparse mode and dense mode. B. By default, the RP is needed only to start new sessions with sources and receivers. C. By default, the RP is needed periodically to maintain sessions with sources and receivers D. RPs are required only when using protocol independent multicast dense mode. Answer: B Explanation: A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM). By default, the RP is needed only to start new sessions with sources and receivers. Reference: https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 3 Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model? A. IPsec B. Cisco Trustsec C. MACsec D. SSL Answer: C Explanation: MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of -band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre Shared Key (PSK) framework. A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a MKA peer) using the current session key. Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16- 9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 4 Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80? A. Deny tcp any any ne 80 Permit tcp any any range 22 443 B. Permit tcp any any ne 80 C. Permit tco any any range 22 443 Deny tcp any any eq 80 D. Deny tcp any any eq 80 Permit tco any any gt 21 it 444 Answer: D
QUESTION NO: 5 To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller. Which EtherChannel mode must be configured on the switch to allow the WLC to connect? A. Active B. On C. Auto D. Passive Answer: B Explanation: Restrictions for Link Aggregation: You can bundle all eight ports on a Cisco 5508 Controller into a single link. Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group. LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch. Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller. If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller. https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
SAP C-BCBTM-2502 - Every day there is someone choosing our exam materials. Google Professional-Data-Engineer - No matter how high your pursuit of the goal, Goldmile-Infobiz will make your dreams become a reality. IBM C1000-201 - We have statistics to tell you the truth. Cisco 300-815 - If you have a IT dream， then quickly click the click of Goldmile-Infobiz. Beyond knowing the answer, and actually understanding the Microsoft AZ-800 test questions puts you one step ahead of the test.
Updated: May 28, 2022
" />
A lot of people who participate in the IT professional certification exam was to use Goldmile-Infobiz's practice questions and answers to pass the exam, so Goldmile-Infobiz got a high reputation in the IT industry. Goldmile-Infobiz is a convenient website to provide training resources for IT professionals to participate in the certification exam. Goldmile-Infobiz have different training methods and training courses for different candidates.
Cisco 350-401 Test Dumps Demo - It can help you to pass the exam successfully.
Do you have tried the 350-401 Test Dumps Demo online test engine? Here we will recommend the 350-401 Test Dumps Demo online test engine offered by Goldmile-Infobiz for all of you. Firstly, 350-401 Test Dumps Demo online training can simulate the actual test environment and bring you to the mirror scene, which let you have a good knowledge of the actual test situation. Secondly, the 350-401 Test Dumps Demo online practice allows self-assessment, which can bring you some different experience during the preparation. You can adjust your 350-401 Test Dumps Demo study plan according to the test result after each practice test.
Only Goldmile-Infobiz can guarantee you 100% success. Goldmile-Infobiz allows you to have a bright future.
350-401 PDF DEMO:
QUESTION NO: 1 Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a Cisco operating system. When all physical connections are mode, the port channel does not establish. Based on the configuration excerpt of SW3, what is the cause of the problem? A. The port-channel interface lead balance should be set to src-mac B. The port-channel trunk is not allowing the native VLAN. C. The port-channel should be set to auto. D. The port channel on SW2 is using an incompatible protocol. Answer: D Explanation: The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 2 Which statement about multicast RPs is true? A. RPs are required for protocol independent multicast sparse mode and dense mode. B. By default, the RP is needed only to start new sessions with sources and receivers. C. By default, the RP is needed periodically to maintain sessions with sources and receivers D. RPs are required only when using protocol independent multicast dense mode. Answer: B Explanation: A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM). By default, the RP is needed only to start new sessions with sources and receivers. Reference: https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 3 Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model? A. IPsec B. Cisco Trustsec C. MACsec D. SSL Answer: C Explanation: MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of -band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre Shared Key (PSK) framework. A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a MKA peer) using the current session key. Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16- 9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 4 Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80? A. Deny tcp any any ne 80 Permit tcp any any range 22 443 B. Permit tcp any any ne 80 C. Permit tco any any range 22 443 Deny tcp any any eq 80 D. Deny tcp any any eq 80 Permit tco any any gt 21 it 444 Answer: D
QUESTION NO: 5 To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller. Which EtherChannel mode must be configured on the switch to allow the WLC to connect? A. Active B. On C. Auto D. Passive Answer: B Explanation: Restrictions for Link Aggregation: You can bundle all eight ports on a Cisco 5508 Controller into a single link. Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group. LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch. Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller. If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller. https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
SAP C-BCBTM-2502 - Every day there is someone choosing our exam materials. Google Professional-Data-Engineer - No matter how high your pursuit of the goal, Goldmile-Infobiz will make your dreams become a reality. IBM C1000-201 - We have statistics to tell you the truth. Cisco 300-815 - If you have a IT dream， then quickly click the click of Goldmile-Infobiz. Beyond knowing the answer, and actually understanding the Microsoft AZ-800 test questions puts you one step ahead of the test.
350-401 Test Dumps Demo & Cisco Study 350-401 Reference - Implementing Cisco Enterprise Network Core Technologies 350-401 Encor - Goldmile-Infobiz
It is the leader in all training materials. It not only can help you to pass the exam , you can also improve your knowledge and skills. Help you in your career in your advantage successfully. You can find their real comments in the comments sections. There must be good suggestions for you on the 350-401 Test Dumps Demo learning quiz as well. Dreams and hopes are important, but more important is to go to practice and prove.
CCNP Enterprise 350-401 The dumps are provided by Goldmile-Infobiz.
Goldmile-Infobiz will provide good training tools for your Cisco certification 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Test Dumps Demo exam and help you pass Cisco certification 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Test Dumps Demo exam. However, our promise of "No help, full refund" doesn't shows our no confidence to our products; oppositely, it expresses our most sincere and responsible attitude to reassure our customers. With our professional VCE 350-401 Dumps exam software, you will be at ease about your VCE 350-401 Dumps exam, and you will be satisfied with our after-sale service after you have purchased our VCE 350-401 Dumps exam software.
A lot of people who participate in the IT professional certification exam was to use Goldmile-Infobiz's practice questions and answers to pass the exam, so Goldmile-Infobiz got a high reputation in the IT industry. Goldmile-Infobiz is a convenient website to provide training resources for IT professionals to participate in the certification exam. Goldmile-Infobiz have different training methods and training courses for different candidates.
Cisco 350-401 Test Dumps Demo - It can help you to pass the exam successfully.
Do you have tried the 350-401 Test Dumps Demo online test engine? Here we will recommend the 350-401 Test Dumps Demo online test engine offered by Goldmile-Infobiz for all of you. Firstly, 350-401 Test Dumps Demo online training can simulate the actual test environment and bring you to the mirror scene, which let you have a good knowledge of the actual test situation. Secondly, the 350-401 Test Dumps Demo online practice allows self-assessment, which can bring you some different experience during the preparation. You can adjust your 350-401 Test Dumps Demo study plan according to the test result after each practice test.
Only Goldmile-Infobiz can guarantee you 100% success. Goldmile-Infobiz allows you to have a bright future.
350-401 PDF DEMO:
QUESTION NO: 1 Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a Cisco operating system. When all physical connections are mode, the port channel does not establish. Based on the configuration excerpt of SW3, what is the cause of the problem? A. The port-channel interface lead balance should be set to src-mac B. The port-channel trunk is not allowing the native VLAN. C. The port-channel should be set to auto. D. The port channel on SW2 is using an incompatible protocol. Answer: D Explanation: The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 2 Which statement about multicast RPs is true? A. RPs are required for protocol independent multicast sparse mode and dense mode. B. By default, the RP is needed only to start new sessions with sources and receivers. C. By default, the RP is needed periodically to maintain sessions with sources and receivers D. RPs are required only when using protocol independent multicast dense mode. Answer: B Explanation: A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM). By default, the RP is needed only to start new sessions with sources and receivers. Reference: https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 3 Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model? A. IPsec B. Cisco Trustsec C. MACsec D. SSL Answer: C Explanation: MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of -band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre Shared Key (PSK) framework. A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a MKA peer) using the current session key. Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16- 9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 4 Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80? A. Deny tcp any any ne 80 Permit tcp any any range 22 443 B. Permit tcp any any ne 80 C. Permit tco any any range 22 443 Deny tcp any any eq 80 D. Deny tcp any any eq 80 Permit tco any any gt 21 it 444 Answer: D
QUESTION NO: 5 To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller. Which EtherChannel mode must be configured on the switch to allow the WLC to connect? A. Active B. On C. Auto D. Passive Answer: B Explanation: Restrictions for Link Aggregation: You can bundle all eight ports on a Cisco 5508 Controller into a single link. Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group. LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch. Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller. If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller. https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
SAP C-BCBTM-2502 - Every day there is someone choosing our exam materials. Google Professional-Data-Engineer - No matter how high your pursuit of the goal, Goldmile-Infobiz will make your dreams become a reality. IBM C1000-201 - We have statistics to tell you the truth. Cisco 300-815 - If you have a IT dream， then quickly click the click of Goldmile-Infobiz. Beyond knowing the answer, and actually understanding the Microsoft AZ-800 test questions puts you one step ahead of the test.
