Goldmile-Infobizの問題集はIT専門家がCiscoの350-401日本語版問題解説「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験について自分の知識と経験を利用して研究したものでございます。Goldmile-Infobizの問題集は真実試験の問題にとても似ていて、弊社のチームは自分の商品が自信を持っています。Goldmile-Infobizが提供した商品をご利用してください。 弊社のCiscoの350-401日本語版問題解説練習問題を利用したら、あなたは気楽に勉強するだけではなく、順調に試験に合格します。多くの人々はCiscoの350-401日本語版問題解説試験に合格できるのは難しいことであると思っています。 弊社が提供したすべての勉強資料と他のトレーニング資料はコスト効率の良い製品で、サイトが一年間の無料更新サービスを提供します。
CCNP Enterprise 350-401 ここにはあなたが最も欲しいものがありますから。
CCNP Enterprise 350-401日本語版問題解説 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Goldmile-Infobizの商品はとても頼もしい試験の練習問題と解答は非常に正確でございます。 そうすれば、実際の350-401 試験関連赤本試験を受けるときに緊張をすることはないです。ですから、心のリラックスした状態で試験に出る問題を対応することができ、あなたの正常なレベルをプレイすることもできます。
350-401日本語版問題解説試験はCiscoのひとつの認証試験でIT業界でとても歓迎があって、ますます多くの人が350-401日本語版問題解説「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験に申し込んですがその認証試験が簡単に合格できません。準備することが時間と労力がかかります。でも、Goldmile-Infobizは君の多くの貴重な時間とエネルギーを節約することを助けることができます。
Cisco 350-401日本語版問題解説認定試験の真実の問題に会うかもしれません。
ご客様は弊社の350-401日本語版問題解説問題集を購入するかどうかと判断する前に、我が社は無料に提供するサンプルをダウンロードして試すことができます。それで、不必要な損失を避けできます。ご客様は350-401日本語版問題解説問題集を購入してから、勉強中で何の質問があると、行き届いたサービスを得られています。ご客様は350-401日本語版問題解説資格認証試験に失敗したら、弊社は全額返金できます。その他、350-401日本語版問題解説問題集の更新版を無料に提供します。
あなたが任意の損失がないようにもし試験に合格しなければGoldmile-Infobizは全額で返金できます。近年、IT業種の発展はますます速くなることにつれて、ITを勉強する人は急激に多くなりました。
350-401 PDF DEMO:
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 3
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
この悩みに対して、我々社Goldmile-InfobizはCiscoのAmazon SAA-C03-JPN試験に準備するあなたに専門的なヘルプを与えられます。 Microsoft DP-600 - Goldmile-Infobizを利用したら、試験に合格しないことは絶対ないです。 Oracle N16302GC10 - 勉強中で、何の質問があると、メールで我々はあなたのためにすぐ解決します。 Huawei H19-401_V2.0 - 私のように、以前が努力しなかったので、今は無駄に悩んでいます。 私たちのMicrosoft AZ-104J練習資料を利用したら、Microsoft AZ-104J試験に合格した人がかなり多いです。
Updated: May 28, 2022