Goldmile-InfobizはCiscoの350-401更新版「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」試験に関する完全な資料を唯一のサービスを提供するサイトでございます。Goldmile-Infobizが提供した問題集を利用してCiscoの350-401更新版試験は全然問題にならなくて、高い点数で合格できます。Cisco 350-401更新版試験の合格のために、Goldmile-Infobizを選択してください。 Goldmile-Infobizが提供するCiscoの350-401更新版認証試験問題集が君の試験に合格させます。テストの時に有効なツルが必要でございます。 弊社の商品は試験の範囲を広くカバーすることが他のサイトがなかなか及ばならないです。
CCNP Enterprise 350-401 ショートカットは一つしかないです。
CCNP Enterprise 350-401更新版 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) 不思議を思っていますか。 Goldmile-Infobizは現在の実績を持っているのは受験生の皆さんによって実践を通して得られた結果です。真実かつ信頼性の高いものだからこそ、Goldmile-Infobizの試験参考書は長い時間にわたってますます人気があるようになっています。
それはもちろんGoldmile-Infobizの350-401更新版問題集ですよ。350-401更新版試験の準備をするとき、がむしゃらにITに関連する知識を学ぶのは望ましくない勉強法です。実際は試験に合格するコツがあるのですよ。
Cisco 350-401更新版 - PayPalは国際的に最大の安全的な支払システムです。
どのようにCisco 350-401更新版試験に準備すると悩んでいますか。我々社の350-401更新版問題集を参考した後、ほっとしました。弊社の350-401更新版ソフト版問題集はかねてより多くのIT事業をしている人々は順調にCisco 350-401更新版資格認定を取得させます。試験にパースする原因は我々問題集の全面的で最新版です。
なぜならば、IT職員にとって、Ciscoの350-401更新版資格証明書があるのは肝心な指標であると言えます。自分の能力を証明するために、350-401更新版試験に合格するのは不可欠なことです。
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
あなたはSAP C_S4CPB_2508練習問題を選ばれば、試験に合格できますよ！ あなたはこれらのFortinet FCSS_SDW_AR-7.4-JPN資格認定を持つ人々の一員になれると、いい仕事を探させます。 Goldmile-Infobizは認定で優秀なIT資料のウエブサイトで、ここでCisco Microsoft AZ-900-JPN認定試験の先輩の経験と暦年の試験の材料を見つけることができるとともに部分の最新の試験の題目と詳しい回答を無料にダウンロードこともできますよ。 我々のCisco CIPS L4M5問題集を購買するのはあなたの試験に準備する第一歩です。 Salesforce Sales-101 - こうして、君は安心で試験の準備を行ってください。
Updated: May 28, 2022